|
09-24-2022, 04:31 PM | #1 |
Jr. Member
Join Date: Sep 2022
Posts: 1
|
2020 Vulcan Vaquero Engine Stalling
I have a 2020 Vulcan Vaquero with less than 5,000 miles on it. I have noticed as a more common issue that the bike just stalls. It stalls at idle, while riding and just normal operation. My bike is modified now and still experiencing the issue of the engine stalling and was having the same issues before I installed any kind of modifications. I originally thought it was due to a bad sensor or the connection on the kickstand kill switch sensor just got dirty all the time. I ended up cutting the wires to the sensor and hardwired it together. I would have issues restarting it or would have issues starting the bike at all no matter how many times I switched from off to on with the ignition or switched the engine kill switch on or off and in order for it to start I would have to put down the kickstand and pull it back up. Which is why I decided to hard wire the system to just keep constant power flowing so it wouldn't think the kickstand came down or fell down during riding. It runs but still having issues with engine stall. I don't really know where to start with the issue as far as diagnosing it. I do not notice any sort of issues when I do ride it such as sluggish acceleration or just other behaviors in regards to the bike not operating mechanically ill. Any sort of suggestions and insight to find out what is causing this issue is welcome.
List of modifications: Ivan tune done Sept. of 2022 Freedom performance racing true duals Roaring Toyz air cleaner Kicker 45KM654L speakers in fairing Thanks in advance for the replies. Really hoping to find a fix or at least find pointers on how to diagnose it further. Would really hate to sell the bike as I really do enjoy it. Login or Register to Remove Ads
Last edited by 2016Broncos; 09-24-2022 at 04:38 PM.
Reason: Trying to bring attention to post to trouble shoot the mechanical issues.
|
|
09-24-2022, 07:10 PM | #2 |
Top Contributor
Join Date: Feb 2008
Location: Ontario
Posts: 6,982
|
Isn't the bike still under warranty ?
Did a dealer ever look at the stalling issue before you did the modifications ? Is the idle speed at the correct RPM ? I think you can change the idle speed somehow. Hopefully someone else will chime in. It's been a while since I had a 1700 Vulcan. |
|
09-24-2022, 07:18 PM | #3 |
Top Contributor
Join Date: Feb 2008
Location: Ontario
Posts: 6,982
|
From the service manual.
Engine stalls easily. Spark plug dirty, broken or gap maladjusted Inspect and replace (see chapter 2). Ignition coil trouble Inspect (see chapter 16). Accelerator position sensor trouble Inspect (see chapter 3). Throttle position sensor trouble Inspect (see chapter 3). ETV actuator trouble Inspect (see chapter 3). Inlet air pressure sensor trouble Inspect (see chapter 3). Water temperature sensor trouble Inspect (see chapter 3). Inlet air temperature sensor trouble Inspect (see chapter 3). Fuel pump trouble Inspect (see chapter 3). Fuel injector trouble Inspect (see chapter 3). Fuel pressure too low or too high Inspect (see chapter 3). Fuel pressure regulator trouble Inspect fuel pressure and replace fuel pump (see chapter 3). Fuel line clogged Inspect and repair (see chapter 3) |
|
09-24-2022, 07:34 PM | #4 |
Top Contributor
Join Date: Feb 2008
Location: Ontario
Posts: 6,982
|
Take a look at section 2-17, 2-18, 2-19 and 2-20 of the service manual to adjust the idle speed.
Standard idle speed (engine warm) is 950 rpm plus or minus 50rpm. |
|
09-24-2022, 10:02 PM | #5 |
Join Date: Apr 2012
Location: NE Indiana
Posts: 996
|
have you ever cleaned the throttle body?
__________________
Troy Donat VBA #02401 2015 Voyager 2006 1600 Nomad black(sold) 2016 Salem, Antlers, 2017 Eureka Springs, Lake George, Antlers 2018 Custer NR, Antlers Login or Register to Remove Ads |
|
09-25-2022, 11:43 AM | #6 |
Join Date: Oct 2013
Location: chandler okla
Posts: 854
|
What Troy Said !
|
|