|
12-18-2020, 11:32 AM | #1 |
Advanced Member
Join Date: Dec 2017
Location: Green Bay WI
Posts: 766
|
Mean Streak wiring diagram
Anyone got a complete wiring diagram or factory manual specific to the Mean Streak? I'm looking for diagrams and info to detail the speedometer and tach for the Mean Streak. Thanks.
__________________
My $1200 Vulcan, to start from. Login or Register to Remove Ads |
|
12-18-2020, 04:53 PM | #2 |
Sr. Member
Join Date: Jul 2016
Location: Somewhere South of Alaska....
Posts: 2,359
|
Clymer repair manuals have a colored electrical schematics....I'd scan mine in, but the powers that be are kinda funky about putting certain materials out on web sites....the clymers are pretty comprehensive....hope this helps....
__________________
--------------------- Don't start no schit, there won't be no schit.... *My Sarcasm is directly proportional to the amount of Stupidity involved* --------------------- VBA#03239 VROC#37400 VRA --------------------- 2014 Vaquero 2001 Nomad FI 2003 Street Glide (sold) 1500 Meanie, fresh rebuild (sold) 90s BUBF Bobber (sold) 2001 UltraCycle FatPounder (Sold) 1975 HD ElectraGlide (Sold) 1982 Kawasaki Z1 Chopper (Sold) Suck It Up & Ride! |
|
12-18-2020, 05:38 PM | #3 |
Advanced Member
Join Date: Dec 2017
Location: Green Bay WI
Posts: 766
|
Thanks. I basically need to see the connections from the crankshaft speed sensors to the ECU to the gauge unit on the Mean Streak. I'm guessing the connections are similar to those for the 1700 crankshaft sensor to the ECU and to the gauge set. Basically I'm looking for the details on getting an engine speed signal to the 1700 gauge set I plan to use on my 1600 frame mounted faring setup.
__________________
My $1200 Vulcan, to start from. |
|
12-21-2020, 08:55 AM | #4 |
Join Date: Mar 2019
Location: K.c. Missouri
Posts: 128
|
I was looking last night after you posted in the other thread
__________________
Love team green owned almost all of them from atvs to baggers and even a lawn mower My dog is my co pilot |
|
12-21-2020, 02:54 PM | #5 |
Advanced Member
Join Date: Dec 2017
Location: Green Bay WI
Posts: 766
|
Just betting on Kawasaki using the same sensor and signal system from the crankshaft sensor to the gauges on a Meanie being basically the same on the 1700 Voyager and Vaquero.
__________________
My $1200 Vulcan, to start from. Login or Register to Remove Ads |
|
03-04-2021, 07:30 PM | #6 |
Advanced Member
Join Date: Dec 2017
Location: Green Bay WI
Posts: 766
|
I did find a complete wiring diagram for a Mean Streak. It shows the Mean Streak has a different ECU than doe the Classic and Nomad, even though the engine and chassis are very similar. By the way the ECU past number for the Classic and Nomad is 21175-0012. The ECU part number for the Mean Streak is 21175-0048. Looking at the wiring diagram one of the obvious differences is the Mean Streak has a tach that the Classic and Nomad do not have. Yet all VN1600 models use the same speed sensor reading the output gear (15 teeth).
The MS ECU has the same number of pins as does the ECU for the Classic or Nomad. But, not all the same pins are used on the MS versus the Classic and Nomad. The wiring diagram for the MS does show the speed sensor output goes to the ECU, and the ECU has two wires up to the tach. The wiring diagram for the Classic and Nomad also show the speed sensor output goes to the ECU, but the wires from the ECU go to the distance sensor in the center console. I'd attach a jpg of the wiring diagram but the system says the file is too large.
__________________
My $1200 Vulcan, to start from.
Last edited by andyvh1959; 03-04-2021 at 07:42 PM.
|
|
03-05-2021, 03:00 PM | #7 |
Join Date: Mar 2019
Location: K.c. Missouri
Posts: 128
|
So are you thinking a meanstreak ecu could run our bikes but also give a tach signal? Gonna be in the garage today trying to get my speedo to run 60 mph
__________________
Love team green owned almost all of them from atvs to baggers and even a lawn mower My dog is my co pilot |
|
03-05-2021, 04:43 PM | #8 |
Advanced Member
Join Date: Dec 2017
Location: Green Bay WI
Posts: 766
|
Maybe, maybe on the Mean Streak ECU, that's assuming the MS ECU is also CANBUS to the tach. But also the output from the MS ECU would have to be the same as to the VN1700 tach to communicate on the CANBUS. So many "ifs".
If I had access to a MS ECU I would just try it. But I'm not buying a MS ECU just to find out. Every MS ECU I shopped on Ebay was over $200 to almost $400.
__________________
My $1200 Vulcan, to start from. |
|
03-12-2021, 12:12 AM | #9 |
Join Date: Mar 2019
Location: K.c. Missouri
Posts: 128
|
Damn that's high for an ecu on a bike that's been out of production for a while
__________________
Love team green owned almost all of them from atvs to baggers and even a lawn mower My dog is my co pilot |
|