|
11-18-2008, 07:12 PM | #1 |
Jr. Member
Join Date: Nov 2008
Posts: 1
|
oil and oil filter
When removing the oil filter on my 07 Nomad I can't get a ratchet on my oil filter wrench because of the belly under there, I know I can drive a nail through it to take it off but my mechanic says I need to torque it down when putting a new one on, tried it with a belt type but crushed the filter, also what generic oil filter and oil would be good to use. Ended up borrowing the shops oil filter wrench which can be used with an open ended wrench. I see they cost about $60 though. - Any other problems like this out there. $70 to change oil and filter at shop seems ridiculous - Midnight
Login or Register to Remove Ads |
|
11-18-2008, 09:39 PM | #2 |
Sr. Contributor
|
oil and oil filter
If your mechanic stated you needed to torque it down, I'd run..... Oil filters need only be tight enough not to leak, period. I tighten my oil filters as tight as I can with my fingertips only, no tighter. It take about as much to break my filter loose as it does opening a jar of mayo. Your making a mistake if you need a filter wrench on a oil filter. Walmart ST7313.
__________________
I love my Victory Cross Country Tour 106. Smells like Victory! Ultra's are Limited There are two types of Harley riders. Those that trailer them and those that push them. The most Interesting Man in the World "Find the things in life you don't do well and don't do those things" Member # 0005 |
|
11-18-2008, 09:44 PM | #3 |
Advanced Member
Join Date: Jul 2007
Location: Morinville, AB
Posts: 904
|
oil and oil filter
Midnight
......Welcome to the forum. Lots of good people and info here. I usually use a long screwdriver, drive it through the filter and get er' loose that way. I have never torqued an oil filter on. Lube the gasket, spin it on til contact, get a good grip on it with your hands, and tighten it up. Most filters manufacturers ask for 1/2 to 3/4 turn after contact and you can do that by hand. I have never had one leak or come loose doing it that way. Check out this site.... http://www.gadgetjq.com/gadgetsfixitpage.htm ....Everything you need to know about filters and oil, and lots of other stuff, can be found there. Don't be afraid to ask questions here. Someone here will be able to answer just about anything you need to know about Nomads..... :)
__________________
________________________________ "lomax" 2014 Voyager Mike Donahue Morinville, AB VBA#17 "Every day above ground is a good one!" _________________________________ |
|
11-18-2008, 10:15 PM | #4 |
Join Date: Aug 2007
Location: Newmarket Ontario Canada
Posts: 35,387
|
oil and oil filter
I just tighten my filter barely hand tight, and it never leaks, and is easy to remove by hand as well. When I have tightened them by hand fairly tight I found them very difficult to remove later on, even with a filter wrench.
__________________
2002 Nomad aka Bountyhunter VBA #27 VROC #18951 |
|
11-18-2008, 11:43 PM | #5 |
Sr. Member
Join Date: Jan 2008
Location: Cartersville, Georgia
Posts: 4,838
|
oil and oil filter
Hi Midnight, welcome to the board from NW. Georgia, Like the others stated, when I replace my filter, I spin it on until it makes contact, and go about 1/2 turn more. I have never had one leak, and to get it loose, I have to use both hands to break the seal, and don't have to use a wrench either.
The "book" does state to tighten it to 13 ft lbs, but that is way to tight. Like I've already said, really snug is good enough. ;)
__________________
Cliff "VulcanE" Evans 2005 Blue & Silver 1600 Nomad VBA # 320 VROC # 20381 Login or Register to Remove Ads |
|
11-19-2008, 12:20 AM | #6 |
Sr. Member
Join Date: Apr 2008
Location: Burnsville, NC
Posts: 1,589
|
oil and oil filter
I had the same problem with my 07 the filter was on way too tight from the factory bent an oil filter wrench getting it off . now i just hand tighten like others have said and no problems
__________________
David "BigDave" Hall Burnsville NC VBA #477 2007 Red and Silver Nomad (traded 4/10/2014) 2013 Blue and Black Voyager |
|
11-19-2008, 06:05 AM | #7 |
Sr. Member
Join Date: Jan 2008
Location: Greenville, NC
Posts: 2,729
|
oil and oil filter
I had a filter on so tight that driving and screwdriver through it and trying to take it off, just ripped the filter. Finally got a filter wrench clamped on it and got it worked off. That was the last time I took my bike to a mechanic friend's house to use is lift. He cranked the thing on there waaaay too tight. I hand tightened the filter the last time I changed the oil and no troubles.
__________________
Amy "kawgirl" Neal Greenville, NC 2002 Nomad |
|
11-19-2008, 07:34 AM | #8 |
VBA Founder
Join Date: Jun 2007
Location: Lindale, Texas
Posts: 6,846
|
oil and oil filter
The best oil filter wrench I've found is the one that has a metal bar with a strap connected to it. You put the strap around the oil filter, roll the bar up tight and use a ratchet to twist the bar until the filter breaks loose. The more you twist, the more tension the belt has twisting the oil filter loose.
I learned a long time ago that a motorcycle oil filter needs to only be put on hand tight. Before putting the new filter on, check the oil spicket on the engine and make sure the old rubber seal didn't stick to the engine when taking the old filter off. Dab a little oil on the rubber seal on the new filter and tighten it down as tight as you can by hand only.
__________________
Robert "Trip" Hilliard VBA/KawaNOW - Founder/Past President VBA # 00001 Trip's Website Custer 09, 18 / Maggie Valley 11 / Eureka Springs 09, 17 / Antlers 09, 10, 11, 13, 15, 16, 17, 18 Texas Hill Country / Deals Gap / Colorado / Wyoming / Montana / Utah / More trips for Trip |
|
11-19-2008, 08:02 AM | #9 |
Advanced Member
Join Date: Feb 2008
Location: Northwest Indiana
Posts: 890
|
oil and oil filter
Taking the oil filter off the first time was a real bear, but you can buy an oil filter wrench that fits on a ratchet from Autozone, Pep Boys or Advanced Auto for under $5. I always have one in my tool box. The first time I changed filters, I had to re-ping the flat spots on the adapter so it would grab on to the filter better. If this is the first time you've tried to get something off your 07, if it was put together like mine, everything is overly tight. To get my windshield apart for adjusting, I broke 3 bolts and stripped another. Those guys get in there with air wrenches and just go nuts. Don't over tighten the filter when putting it back on and don't forget to oil the rubber "O-ring".
|
|
11-19-2008, 09:30 AM | #10 |
Sr. Contributor
|
oil and oil filter
"As tight as you can by hand only" Thats still too tight Trip. The expansion and contraction of the heating process over time will make that filter a bear to remove. No more than 1/2 turn after the gasket hits.
__________________
I love my Victory Cross Country Tour 106. Smells like Victory! Ultra's are Limited There are two types of Harley riders. Those that trailer them and those that push them. The most Interesting Man in the World "Find the things in life you don't do well and don't do those things" Member # 0005 |
|
11-19-2008, 10:31 AM | #11 | |
Mega-Contributor
Join Date: Sep 2007
Location: Where it doesn't snow...ever!
Posts: 21,926
|
oil and oil filter
Quote:
__________________
Scott "Cactusjack" Hanks VBA #00105 H.O.G. #4250060 2011 H-D Ultra Limited 103ci :: 2011 HD Electra Glide Ultra Limited w/Stage 1 :: Rallies: Mesquite '08|Custer '09|Cortez '10|Crescent City '11|Kanab '12|Antlers '12|Estes Park '13|Antlers '13|Orofino '14|The Dalles '17 |
|
|
11-19-2008, 10:54 AM | #12 |
Sr. Member
Join Date: Sep 2007
Location: Livermore CA
Posts: 1,334
|
oil and oil filter
I run the filter on till it hits then just 1/4 to 1/2 turn more to tighten.
__________________
Life is Good! Eternal Life is better! |
|
11-19-2008, 02:40 PM | #13 |
Top Contributor
Join Date: Feb 2008
Location: Ontario
Posts: 6,982
|
oil and oil filter
Get a new filter and take it to Napa. They have a have a large sheet metal type socket that goes on the end of the filter that is the same size as the flats on the outside diameter of the filter.
|
|
11-19-2008, 09:12 PM | #14 | |
Member
|
oil and oil filter
Quote:
|
|
|
11-20-2008, 12:14 AM | #15 |
Advanced Member
|
oil and oil filter
I use a screwdriver and drive it through the filter to loosen it up and take it off. When installing the new filter, I only tighten by hand. Haven't had any leaks to this point.
Actually, I have done the same process on all my cars and trucks as well and never had any leaks. Just make sure you put a thin quote of oil around the seal before you install the new filter and you shouldn't have any problems. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Oil and filter | captain | 1700 Nomad, Vaquero & Voyager | 1 | 03-09-2010 05:08 PM |
Oil Filter | phenrichs | Parts & Accessories | 24 | 03-28-2009 10:34 PM |
Oil filter | coloradontexas | 1500 & 1600 Nomad | 10 | 03-28-2009 06:13 PM |
Oil Filter | jazz | 1500 & 1600 Nomad | 10 | 03-16-2009 10:39 AM |
OIL FILTER | kawbuc | Vulcan Nomad/Vaquero/Voyager | 14 | 06-15-2008 06:29 AM |