|
05-28-2011, 09:08 AM | #2 |
Sr. Contributor
Join Date: Apr 2008
Location: Tamworth New Hampster 06 1600
Posts: 12,484
|
speedo
It could be either, depending on the year.. If there is a cable to the ft forks and thence to the wheel hub, not going to the brakes it's a cable drive.
If not it's electric, and has a sencor on the tranny under the left side engine cover, near where the clutch slave is, but further back. Saying clutch slave is to just ID the rough area. Problems could be a bad connection at any, or a bad sender. What else isn't working if anything, as that may lead to a bad connection.
__________________
06 1600 Nomad Just call me Mac molon labe come and get it |
|
05-28-2011, 12:38 PM | #3 |
Member
Join Date: Apr 2008
Location: spring hill florida
Posts: 477
|
speedo
its an 06, but everything else is working fine that i can tell, no cable going to hub, didnt no if it might be a elec. connection, or if needle is just sticking, or if its a female needle and going through PMS,,LOL
|
|
05-28-2011, 03:32 PM | #4 |
Sr. Contributor
Join Date: Apr 2008
Location: Tamworth New Hampster 06 1600
Posts: 12,484
|
speedo
No 06 has cable speedo. That set up is all electronic. Does the needle move on first turn of the key? It should fly all the way to the other side of the meter in the self check test. And then return.
__________________
06 1600 Nomad Just call me Mac molon labe come and get it |
|
05-28-2011, 03:52 PM | #6 |
Sr. Contributor
Join Date: Apr 2008
Location: Tamworth New Hampster 06 1600
Posts: 12,484
|
speedo
Hmmmmmm..... No spiders in the glass where you can see right? No Fla mung growing under there at all?
If not I would pop off the nacell and unplug the connectors there and plug them back in a couple times. Maybe there is mung on the connector pins... I know the smaller connector mostly goes to the key switch, and the larger mostly goes to the speedo unit and does other functions, but pull both apart. That is the devils own work too. The top female connector has a release tab to pull the connectors apart, and the female connector has a under side release to pull it off the frame holder. These are a wicked pain to get at. Then test. If that doesn't work you will need to go deeper. No joke about spiders either. The instrument is that sensitive. The 1600 speedo has a lense that comes right off. The 1500 isn't close to the same..
__________________
06 1600 Nomad Just call me Mac molon labe come and get it |
|
05-28-2011, 04:01 PM | #7 |
Member
Join Date: Apr 2008
Location: spring hill florida
Posts: 477
|
speedo
thanks, had my speedo off a few times and when i put webslinger dial in, maybe just a loose connection, like i said i really dont use my speedo other checking speed when i pass a cop, i shift by feel
|
|
05-28-2011, 04:03 PM | #8 |
Sr. Member
Join Date: Jan 2008
Location: Cartersville, Georgia
Posts: 4,838
|
speedo
B, Been there and done that with the same symptoms on the speedo. If you have a service manual (there is one available third line down in this garage section) go to the electrical section/system and browse through there. It will tell you how to do different kinds of checks on the speedo (they call it a "meter") I ended up replacing mine with one I got off ebay, and it had almost 25,000 less miles on it too.
__________________
Cliff "VulcanE" Evans 2005 Blue & Silver 1600 Nomad VBA # 320 VROC # 20381 |
|
05-28-2011, 04:05 PM | #9 |
Member
Join Date: Apr 2008
Location: spring hill florida
Posts: 477
|
speedo
thanks, do have service manual, so i will read up on it
|
|
05-28-2011, 04:09 PM | #10 |
Sr. Contributor
Join Date: Apr 2008
Location: Tamworth New Hampster 06 1600
Posts: 12,484
|
speedo
I don't use my speedo either much, it just is in a bad place to suit me. If I look down I tend to end up down. The point is I like what is on the bike to be working. I am sure you do to.
I think I have a bad connection on the blue hi beam indicator, but I only get one chance to fix it. Last year it didn't light on first Spring start up and again it didn't this time. Basicly all I did was unplug these 2 connectors and it works again.. I need more trouble with it before I can nail down a cause/fault.
__________________
06 1600 Nomad Just call me Mac molon labe come and get it |
|
05-28-2011, 04:15 PM | #11 |
Member
Join Date: Apr 2008
Location: spring hill florida
Posts: 477
|
speedo
yea, i'm very meticulous when it comes to things, hows NH doing, spend 6 yrs up there in Plaistow as a cop, before getting smart and moving to FL, with 90-100 degree heat,, i think i was smart, but maybe not
|
|
05-28-2011, 04:52 PM | #12 |
Sr. Contributor
Join Date: Apr 2008
Location: Tamworth New Hampster 06 1600
Posts: 12,484
|
speedo
I did my time in Fla. Didn't like the T storms much and didn't like no winta'. 2 years there was enough for me.
Right now it's skeeter hell here, I just walked the dogs and we got ate alive. Worst I seen them in many years right now. Tamworth is just south of the kanc apx 14 miles, so it's woodsie and real buggy. I stay here for 4 reasons. 1 is ok gun laws, 2 is sugar maple since I make the sugar, 3 is decent riding in season with out any need to go very far, and 4 is i can't find a better place to be. I live by seasons, not a clock, so it works well for me.
__________________
06 1600 Nomad Just call me Mac molon labe come and get it |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Speedo Inaccuracy | Netnorske | 1500 & 1600 Nomad | 12 | 09-12-2008 09:22 PM |
Speedo visor | doctorgski | Vulcan Nomad/Vaquero/Voyager | 26 | 09-02-2008 09:14 PM |
Speedo Reading | boots | Vulcan Nomad/Vaquero/Voyager | 16 | 07-29-2008 03:57 PM |
'05 Speedo Sticking? | VulcanE | 1500 & 1600 Nomad | 3 | 07-28-2008 10:26 AM |
Speedo | sturmannderss | 1500 & 1600 Nomad | 17 | 03-17-2008 09:34 AM |